Set F807 to 0. Page 15: Schneider Electric Altivar 212 Hardware setup S1A53844 012011 15 Protection Against Interference Use the Schneider Electric cable with 2 pairs of sh ielded twisted conducto rs (reference: TSXCSA100, TSXCSA200, TSXCSA500).We know from our users experience that most of people do not really attach importance to these manuals.Many instructions, immediately after the purchase, go into the trash along with the box, which is a mistake.
Get acquainted with the information concerning the manual for Schneider Electric Altivar 212, which will help you to avoid troubles in the future. You will then acquire basic knowledge to maintain Schneider Electric Altivar 212 in good operating condition to make it easily reach the intended life cycle. Then you can put away the manual on a shelf and use it again only in a situation where youre not sure whether you perform maintenance of the product appropriately. Proper maintenance is a necessary part of your satisfaction from Schneider Electric Altivar 212. Once a year, clean the closet where you keep all your devices manuals and throw out the ones that you dont use. This will help you maintain order in your home base of manuals. Page 2: Schneider Electric Altivar 212 2 S1A53844 012011 The information provided in thi s documentation conta ins general descri ptions andor technical characteristics of the performance of the pr oducts contained herein. Page 5: Schneider Electric Altivar 212 S1A53844 012011 5 Safety Information Important Information NOTICE Read these instructions carefully, and look at the eq uipment to become famil iar with the device be fore trying to install, operate, or maintain it. Th e following speci al messages may appear throughout this documentati on or on the equipment to warn of potent ial hazards or to. Schneider Electric Altivar 212 How To Configure ThePage 6: Schneider Electric Altivar 212 6 S1A53844 012011 About the Book At a Glance Document Scope The purp ose of this document i s to show you how to configure the Altivar 212 to use Mod bus for monito ring and control. NOTE: Read and unde rstand this document and all rela ted documents (see belo w) before installi ng, operating, or mainta ining your ATV212. Page 7: Schneider Electric Altivar 212 S1A53844 012011 7 (1) For additional information, refer to NEMA ICS 1.1 (latest edi tion), Safety Guidelines for t he Application, Installation, an d Maintenance of Solid State Control a nd to NEMA ICS 7. Sa fety Standards for Construction and Guide for Selection, Installation and Operat ion of Adjustable-Speed Drive S. Page 9: Schneider Electric Altivar 212 S1A53844 012011 9 Introduction 1 Introduction Data exchanges give access to all Altivar 212 functions: Control (start, stop, reset, setpoint), Monitoring (status, current, voltage, thermal state.), Diagnostics (alarms), Settings, Configuration. The communication port has an RJ45 and an open styl e connector for the connectio. Page 10: Schneider Electric Altivar 212 Introduction 10 S1A53844 012011. Page 11: Schneider Electric Altivar 212 S1A53844 012011 11 Hardware setup 2 Hardware setup Whats in this Chapter This chapter contains the following topics: Topic Page Pin out of the Open Style Modbus connector 12 Connection via Open Style wiring system 13 Open Style Reference 13 Pin out of the RJ45 Modbus connector 13 Connection via RJ45 wiring system 14 RJ45 Reference 14 Protec. Page 12: Schneider Electric Altivar 212 Hardware setup 12 S1A53844 012011 Pin out of the Open Style Modbus connector Open Style Connector (screwcage plug style) B A GND Common SCR Shield Note: It is possible to connect two wires inside one cage i n order to be compliant to daisy chain requirement s. Cross section: 0.2 - 2.5 mm AWG 24-12 Tighte ning torque: 0.5-0.6 Nm 4.4-5.3. Schneider Electric Altivar 212 Serial Link ConnectionPage 13: Schneider Electric Altivar 212 Hardware setup S1A53844 012011 13 Connection via Open Style wiring system Open Style Reference Modbus serial link connection is carried out usi ng RS 485 double shielded tw isted pair cables, supplied without connector (reference: TSX CSA 100). Set sw itch. Page 14: Schneider Electric Altivar 212 Hardware setup 14 S1A53844 012011 Connection via RJ45 wiring system Description RJ45 is factory set to connec t the graphic display option. Use the open style connector to c onnect the drive to Modbus fieldbus. Using RJ45 to connect Modbus fieldbus is st ill possibl e but requires to modify parameter Com channel choice F807 value.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |